Home Search
  • LPD-200-X Power Supply
    Ø  AC input selectable by switch (115Vac/230Vac) Ø  High efficiency, long life and high reliability Ø  Output protections: OLP/SCP/OVP/OPP Ø  Wide operating ambient temp (-25℃~70℃) Ø  100% full load burn-in test Ø  Altitude up to 5000m Ø  1U low profile Ø  Cooling by free air convection Ø  3 years warranty SPECIFICATION                                               MODEL LPD-200-12 LPD-200-24 OUTPUT DC Output 12V 24V Rated Current 16.67A 8.33A CurrentRange    Note 1 0~16.67A 0~8.33A Ripple and Noise  Note 2 0~70℃ ≤150mV -25℃ ≤300mV Voltage ADJ. Range 10.2~13.8V 21.6~28.8V Voltage Accuracy ±1.5% ±1.0% Line Regulation ±0.5% Load Regulation ±1.0% ±0.5% Set-up Time ≤2.0S (230/115Vac input, Full load) Hold up Time ≥16mS(230Vac input, Full load)   ≥12mS(115Vac input, Full load) Temperature Coefficient ±0.03%/℃ Overshoot and Undershoot <5.0% INPUT VoltageRange   90Vac~132Vac/180Vac~264Vac FrequencyRange 47Hz~63Hz Efficiency ( Typical) @230Vac ≥86.5% ≥88.5% AC Current (max.) <4.0 A@ 115Vac  ;  <2.2A @ 230Vac 2.5A Inrush Current (Typical) <60A@ 115/230Vac  Cold start Leakage Current Input—output:<0.25mA ; Input—PG:<2.0mA  (Input 240Vac) PROTECTION Over Load 18.33~30.0A, Hiccup mode, auto recovery 9.17~15.0A, Hiccup mode, auto recovery Over power 220~360W, Hiccup mode, auto recovery 220~360W, Hiccup mode, auto recovery Over voltage 13.8~16.2V, Constant voltage, auto recovery 28.8~33.6V, Constant voltage, auto recovery Shorted Circuit Long-term mode, auto recovery ENVIRONMENT Operating amb. Temp. & Hum. -25℃~70℃; 20%~90%RH No condensing Storage Temp. & Hum. -40℃~85℃; 10%~95%RH No condensing SAFETY &EMC Note 3 Safety Standards Meet GB4943 / EN60950 Withstand Voltage Primary-Secondary:3.0KVac/10mA .Primary-PG:2.0KVac/10mA. Secondary-PG:0.5KVDC/10mA. Isolation Resistance 10Mohms EMC Immunity Compliance to EN61000-4-2,3,4,5,6,8,11 OTHERS MTBF (MIL-HDBK-217F) More than 200,000Hrs (25℃, Full load) Dimension (L*W*H) 190×99×30mm Packing TBD Cooling method Cooling by free air convection NOTE 1. All parameters NOT specially mentioned are measured at rated input, rated load and25℃of ambient temperature. 2. Measured at 20MHz of bandwidth by using a12”twisted pair-wire terminated with a 0.1 uF & 10uF parallel capacitor. 3.The power supply is considered as a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies” on https://www.powerld.com
    A total of



Copyright © 2022 Powerld Enterprises Co.,Ltd.. All Rights Reserved.

IPv6 network supported


Leave A Message

Leave A Message

    If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

  • #
  • #
  • #